How To Order
- By Products: Step and Repeat Banner Only | Step and Repeat Banner + Stand | Step and Repeat Banner + Stand + Red Carpet
- By Events: Step and Repeat Backdrop Templates | Banner Templates
- By Size: 2-3 Persons : 4'x8' | 3-4 Persons: 6'x8' | 4-6 Persons: 8'x8' | 6-8 Persons: 10'x8' | 8-10 Persons: 12'x8'
- By Material: Vinyl Step and Repeat | Fabric Step and Repeat
- Manual Order Request - if you have any online order difficulties.
How To Order Step and Repeat from Sign11.com
About Finishing Options
Step 1. Assemble two Horizontal Pole by putting together 2 x (A1) and 2 x (A2) into one Horizontal Pole (A1plus A2).
Step 2. Insert Vertical Pole (B) into the hole on top of the Stand Foot (SF) and secure the Vertical Pole (B) with the Bottom Screw (E-Screw) using the Allen Wrench (AW). Repeat this step to assemble another set (B plus SF).
Step 3. Lay down your Backdrop at the desired display location.
Step 4. Place each Vertical Pole with Stand Foot (B plus SF) at the either side of your Backdrop.
Step 5. Extend the Horizontal Poles (A1 plus A2) as wide as your Backdrop by loosening the knobs. Once extended, secure the size by tighening the knobs.
Step 6. Insert the Horizontal Pole (A1 plus A2) into the top pole pocket of your backdrop.
Step 7. Place the Backdrop onto the stand using 2 x Knob Screws (D-Screws) in the screw hole given on top of each Vertical Poles (B plus SF)
Step 8. Extend the upper part of the Vertical Poles (B) by loosening Should Level Knobs (Ba). DO NOT Extend all the way but leave about 1” of the Pole inside. Secure by tighening the knobs.
Step 9. Insert the remaining Horizontal Pole (A1plus A2) into the bottom pole pocket of your backdrop.
Step 10. Adjust the height of your backdrop by loosening the Hip Level Knobs and raising the Middle Vertical Pole. Secure the height by tightening the knobs.
Step 11. Secure the bottom Vertical Pole (A1 plus A2) using the remaining 2 x Knob Screws (D-Screws).
Step 11A. For those who have Side Grommets on the Backdrop Only!
Using the zip ties provided, secure your backdrop to the vertical poles of the stand.
Step 12. Adjust the backdrop using the Hip Level Knobs and Vertical Poles.
For any questions, please contact us at 1-888-789-1050 or email us at firstname.lastname@example.org
If you need to purchase a part, you can do so on our website www.sign11.com or by emailing us at email@example.com
Pre-spaced pressure sensitive letters are computer cut from vinyl marking films. Vinyl letters and graphics are applied with an application tape for easy pre-spaced installation to any clean, dry, hard, smooth surface.
Before you begin your application, be sure the sign surface is free of dirt, grease and wax to ensure proper adhesion. (It is important to note that vinyl does not adhere well to porous surfaces such as concrete, unpainted wood and most vinyl wall coverings.. so we recommend whenever possible that you pre-test application to the surface prior to final installation.)
Upon arrival, check your order carefully to ensure the letters and graphics match your specifications.
Place graphic on sign surface in desired position, with pre-mask application tape facing up. (Note: Use bottom of straight-edge letters for alignment). Secure in place with masking tape across the top of the protective sheet (called "backing") to create a hinge. For easier application of larger characters or long backings.. cut between every second or third letter after the graphic has been aligned (inset).
Lift backing up away from sign surface, and carefully remove the front liner. This will expose the adhesive on the back of the graphic. Caution: Do not allow the graphic to touch the sign at this time.
Holding the graphic slightly away from the surface, begin application by squeegeeing along the top of entire graphic (download 1" to 2") to ensure a straight start and an even alignment and then continue to burnish down and outwardly with the squeegee.
After the graphic has been firmly suqueegeed, remove the pre-mask tape by peeling it back slowly at an angle of 180 degrees to the surface. When working in temperatures less than 60 degrees, allow the graphic a few minutes to adhere to the sign surface before peeling pre-mask.
Quickly and effectively you have completed your customized sign message. If any air bubbles should appear, puncture with a pin and re-squeegee lightly to remove the air.
Dish detergent and water can be helpful with large graphics that are difficult to handle during installation. A wet application will help prevent the graphic from sticking firmly where you don't want it to from excessive air entrapment and from wrinkling. After Step 1 (above), lift backing up, and with a sponge, wet the surface slightly with soapy water (1 or 2 drops of detergent per cup of water) and then apply the vinyl graphic to the wet area. Working from the top with downward strokes, remove the excess water and foam from underneath the graphic with a squeegee. Gently dry and burnish the graphic with a clean cloth. With this application method, ultimate adhesion of the graphic is reached later than the dry method (24-48 hours( and we recommend that you re-squeegee firmly again a day after initial application.